RADIUM FUEL RAILS SUBARU TOP FEED CONVERSION RAILS SUIT 1999-2000 WRX STI
This fuel rail conversion kit is compatible with the Version 5/6 JDM STi EJ207 and Twin Turbo Legacy GT-B EJ208. It converts the OEM side feed fuel injector setup to top feed, allowing the use of high flow fuel injectors (not included). The fuel rail injector bores are 14mm ID. Each rail features a large internal bore to suit even the most fuel hungry engines. They are CNC machined from solid 6061 aluminum, black anodized, and laser engraved for a high quality surface finish. All 6 fuel rail ports are tapped with 8AN ORB (3/4"-16) threads
Machined phenolic mounting spacers and washers are included to completely isolate the fuel rail from heat transferred from intake manifold and mounting bolts.
The four included machined injector seats press into the intake manifold and seal air tight. They are anodized and laser etched and are designed for 14mm diameter lower O-ring injectors.
Below are some of the many fuel injectors that are a direct fitment with this Radium fuel rail kit:
Injector Dynamics ID725-48-14-14
Injector Dynamics ID850-48-14-14
Injector Dynamics ID1000-48-14-14
Injector Dynamics ID1050x-48-14-14
Injector Dynamics ID1300-48-14-14
Injector Dynamics ID1700-48-14-14
Injector Dynamics ID2000-48-14-14
Evolved Injection EI550-48-14-14
Evolved Injection EI650-48-14-14
Evolved Injection EI850-48-14-14
Evolved Injection EI1000-48-14-14
Evolved Injection EI1200-48-14-14
Evolved Injection EI1300-48-14-14
Evolved Injection EI2200-48-14-14
This fuel rail conversion kit is compatible with all fuel types including popular alcohol mixtures such as E85.
-Black Anodized Laser Etched Aluminum Fuel Rails (x2)
-Black Anodized Ver5/6 JDM Conversion Fuel Rail Mount (x2)
-Black Anodized and Laser Etched Injector Seats (x4)
-Phenolic Thermal Insulating Press-In Spacers (x4)
-Phenolic Thermal Insulating Press-In Bolt Washers (x4)
-Stainless Steel Hardware
-Black Anodized Aluminum 6AN Male Fittings (x4)
-Black Anodized Aluminum 8AN ORB Plugs (x4)
The 20-0304-01 kit includes enough to plumb the rails in "Parallel, Flow-Through" or "Series". Refer to the More Details tab above for more information. If -8AN male fittings are required, they can be purchased here 14-0152. Two of the plugs can be used if the fuel rails will be plumbed in "Parallel, Dead End", as shown. The other two plugs can be used for the lower center ports if a fuel pulse damper is not used.
NOTE: Neither fuel rail kit comes with hoses.
Do I need a pulse damper?
The opening and closing of the injectors creates pressure pulses in the fuel rail, which can lead to unstable fuel pressure. In order to achieve a safe and consistent rail pressure, a pulse damper should be used (especially with high flow injectors). The internal diaphragm will absorb oscillating pulses and stabilize fuel pressure. This correction can be measured throughout the RPM range and can often help an erratic surging idle.
The optional Radium 20-0176 fuel pulse damper can be used in any of the three -8AN ORB ports on these fuel rails.
Want to reuse the OEM Subaru FPR?
If the OEM 2-bolt flanged FPR will be reused, select one of the OEM FPR options above. The 20-0301 OEM FPR adapter is commonly used with EJ20 engines and 20-0303 is used with EJ25 engines (excluding STi). MEASURE YOUR OEM FPR BEFORE ORDERING. These adapters can be used in any of the ports and permits properly clocking for appropriate fitment.